murf1020ct thru murf1060ct glass passivated super fast rectifier reverse voltage - 200 -600 volts forward current - 10.0amperes r semiconductor notes : 1. pulse test: 300 s pulse width,1% duty cycle 2. reverse recovery test conditions i =0.5a,i =1.0a, irr=0.5a 3. thermal resistance from junction to case fr maximum ratings and electrical characteristics (ratings at 25 c ambient temperature unless otherwise specified ,single phase ,half wave ,resistive or inductive load. for capacitive load,derate by 20%.) maximum repetitive peak reverse voltage v rrm v olts v olts v olts v olts a a mps a mps v rms v dc i (av) i fsm t stg v f i r r jc maximum rms voltage maximum dc blocking voltage maximum average forward (see fig.1) rectified current maximum instantaneous forward voltage at 5.0 a per leg(note 1 ) t =25 c t =125 c a a typical thermal (note ) resistance 3 operating junction temperature range storage temperature range maximum instantaneous reverse current at rated dc blocking voltage(note 1) peak forward surge current 8.3ms single half sine-wave superimposed on rated load (jedec method) -55 to+150 -55 to+150 3.0 c/w c c t j 400 280 400 150.0 symbols units murf 1040ct features mechanical data plastic package has underwriters laboratory flammability classification 94v-0 single rectifier construction high surge capability for use in low voltage ,high frequency inverters, free wheeling ,and polarity protection applications high temperature soldering guaranteed:2 0 c/10 seconds, 0.25"(6.35mm)from case fast switching for high efficiency low forward voltage drop 6 component in accordance to rohs 2011 65 eu // 5.0 150 1.3 250 maximum reverse recovery time (note 2) trr 35 ns 200 140 200 murf 1020ct 600 420 600 murf 1060ct per leg total device 10.0 0.975 1.7 5 jf murf1020ct case: jedec ito-220ab molded plastic body terminals: lead solderable per mil-std-750,method 2026 polarity: as marked. any mounting position: jinan jingheng electronics co., ltd. http www.jinghenggroup.com :// 9-28 dimensions in inches and (millimeters) ito-220ab 1.161(29.5) 0.177(4.50) 0.104(2.64) 0.029(0.73) 0.111(2.83) 0.140(3.55) 0.110(2.80) 0.187(4.75) 0.272(6.90) 0.551(14.00) 0.029(0.73) 1.083(27.5) 0.138(3.50) 0.096(2.44) 0.019(0.47) 0.101(2.57) 0.128(3.25) dia 0.102(2.60) 0.167(4.25) 0.256(6.50) 0.512(13.00) 0.019(0.47) pin 123 0.130(3.31) 0.111(2.81) 0.056(1.43) 0.043(1.10) 0.410(10.41) 0.390(9.91) 0.067(1.70) 0.059(1.50)
0 20 40 60 80 100 120 150 0 2 4 6 8 10 12 fig.1-forward current derating curve fig.2-maximum non-repetitive peak forward surge current fig.3-typical instantaneous forward characteristics fig.4-typical reverse characteristics average forwa rd curren t amperes reverse voltage. volts t, pulse duration ,sec. lead temperature ( c) resistive or inductve load 1 10 0.1 0.1 0.1 0.01 1 1 10 10 100 100 10 400 100 100 fig.5-typical junction capacitance fig.6-typical transient thermal impedance junction capacitance(pf) transient therma l impedance, c/ w t =25 c f=1.0mh j z vsig=50mvp-p ratings and characteristic curves murf1020ct thru murf1060ct 180 0.01 0.1 1 50 10 0 0.4 0.2 0.8 1.0 0.6 1.2 1.6 1.8 1.4 2.0 2.2 2.4 instantaneous forwa rd curren t( amperes) instantaneous forward voltage (volts) pulse width=300 s 1% duty cycle 200v 400v 600v 0.001 0.01 1 0.1 10 20 20 0 40 60 80 100 instantaneous reverse current ( a) percent of rated peak reverse voltage% t =25 c j t =100 c j jinan jingheng electronics co., ltd. http www.jinghenggroup.com :// 9-29 0 40 20 60 100 80 1 10 100 peak forward surge current(amperes) number of cycles at 60hz 8.3ms single half sine wave (jedec method) - 50 20 5 2 120 140
|
